2023 Fatbook Canadian Catalogue Drag Specialties

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2023. SECTION 1 2023 NEW PRODUCTS NP74 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. RACE SERIES® OIL SYSTEM PACKS FOR TWIN CAM • Quieter and smoother engine operation • Increase oil pressure, scavenge volume and engine oil flow • 25-35 degree cooler engine temperatures • 15-30 degree cooler oil temperatures • 15-30 more psi of oil pressure • Eliminate wet sumping, blowby and oily air cleaners • Test results show 3 horsepower gain and 4 ft./lb. of torque gain to the rear wheel • Billet 7075 aluminum oil pump is 50% harder and stronger than the factory pump; holds tighter tolerances under temperature • Includes Race Series oil pump, Race Series short-travel hydraulic roller lifters, high flow cam plate and cam installation kit • Race Series short-travel hydraulic lifters have .115" of total travel and will increase rpm by decreasing valve float and valve-train harmonics while maintaining a quiet engine PART # DESCRIPTION 0932-02911 For 07-17 Twin Cam and 06 Dyna w/ gear or chain drive 0932-0289 For 99-06 Twin Cam (except 06 Dyna) w/ gear driven cams 0932-0290 For 99-06 Twin Cam (except 06 Dyna) w/ chain driven cams 0932-02922 For 99-06 Twin Cam (except 06 Dyna) w/ chain drive conversion camplates upgrade to 07-17 hydraulic tensioners 1 Gear Drive cam systems require block-off plate kit PART #0932-0036. 2 Conversion camplates use 99-06 style camshafts; oil system pack requires separate purchase of hydraulic chain drive tensioners, chains, sprockets and spacers. • The travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration inside the lifter on steep, fast action high lift camshaft lobes • See page 570 of the 2023 Parts Canada FatBook for the entire line of Feuling Race Series Oil System Packs for Twin Cam NOTE: Use with short-travel pushrods PART #0928-0116 on stock base circle camshafts (Feuling 525, 543 and 574 grinds) and PART #0928-0117 on small base circle camshafts (Feuling 594 and 630 grinds). NOTE: Optional Feuling x ARP oil pump/​camplate bolt kit available PART #2401-0993. REAPER® 538 CAM FOR M-EIGHT • Produce more power and torque in the riding rpm range, improving throttle response, acceleration and fuel mileage • Smooth camshaft lobe ramps are easier on valvetrain components and eliminate excessive valvetrain noise and wear • Dyno proven and track tested • Aggressive camshaft with a nasty sound • Revs up fast and pulls hard in engines with big bore cylinders, modified cylinder heads, intake, compression and exhaust • The Reaper 538 grind will shine in 124" and larger cubic inch engines with added compression ratio • Ported cylinder heads are not required, but will complement the cam and add even more pulling power throughout the range • The stock throttle body produces an excellent powerband and use of a high-flow throttle body will increase peak power numbers • A high-flow exhaust system and air cleaner is highly recommended for optimal performance • Feuling recommends matching this cam with Race Series oiling system • High lift valve springs are required on stock cylinder heads; see Feuling Beehive valve spring kit PART #0926-2973 on page 523 of the 2023 Parts Canada FatBook GRIND VALVE LIFT OPEN CLOSE DURATION @.053" LIFT @ TDC LOBE CENTERLINE CAM SPECS MEASURED IN THE ENGINE ON THE LIFTER @ .050" USING A 1.61 ROCKER ARM RATIO Intake .538 20.5° 38.5° 239° .180" 99° Exhaust .542 48° 18° 246° .157" 105° PART # DESCRIPTION 0925-1372 For 17-22 M-Eight • SE cylinder heads have high lift valve springs, but will need to be verified • Heavy-duty one piece pushrods are also highly recommended; see PART #0928-0091 on page 528 • 2250 - 6250 rpm range • Made in the U.S.A. • See pages 548-549 of the 2023 Parts Canada FatBook for the entire line of Feuling Reaper cams 0932-0291