WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 2 All part numbers in BLUE are new for 2024. 125 See OLDBOOK For Early Model Applications PART # DESCRIPTION 0636-0059 Handlebar/rail base for 3/8” - 5/8” dia. rails 0636-0060 Handlebar/rail base for 3/4” - 1” dia. rails 0636-0061 Handlebar/rail base for 1 1/8” - 1 1/2” dia. rails RAM MOUNT TORQUE™ HANDLEBAR/RAIL BASES WITH 1” BALL • Low-profile mounts are the perfect way to secure your personal electronics and small accessories in any high-vibration environment • Bases utilize nylon-insert locknuts to prevent loosening from vibration • Includes sizing inserts to provide a snug fit and rail protection PART # DESCRIPTION 0603-0891 Brake/clutch reservoir base w/ 1” ball RAM MOTORCYCLE BRAKE/CLUTCH RESERVOIR BASE WITH 1” BALL • Powdercoated marine-grade aluminum • 1” B-size rubber ball • Connects to handlebar clutch/brake on left or right side • Includes 40mm x 6mm stainless steel hardware • Hole centers on base have a minimum width of 0.94” and a maximum of 1.58” PART # DESCRIPTION 0636-0058 Brake/clutch reservoir base RAM MOUNT MOTORCYCLE BRAKE/CLUTCH RESERVOIR BASE WITH 1” BALLS • Mount electronic devices to your handlebar brake/clutch clamp • Holds two 1” diameter mounting balls • Ball that is connected between hole centers is removable • Includes 40mm x 6mm stainless steel hardware NOTE: To see if this base will mount to your motorcycle, check hole spacing of base against your clutch/brake reservoir. The holes’ centers have a minimum width of 0.94” and a maximum of 1.58”. PART # DESCRIPTION 0603-0828 RAM Track Ball™ w/ T-bolt attachment RAM TRACK BALL™ WITH T-BOLT ATTACHMENT • B-size, 1” rubber ball molded to a high-strength composite base • Rubber friction washer and a stainless steel T-bolt for sliding into virtually any track system • Insert or slide the Track Ball™ into your track and twist the ball clockwise to tighten in place; twist counterclockwise to loosen PART # DESCRIPTION 0603-0827 Tough-Track™ composite 3” track RAM TOUGH-TRACK™ TOP-LOADING COMPOSITE 3” TRACK • High-strength composite • Can be drilled to any flat surface • Designed to use with #10 screws for easy installation, hardware not included • Works with a wide variety of RAM track bases to attach cameras, fishing rods, phones, etc. • Dimensions: 4.75” L x 1.75” W • Track thickness .35”, inside track length 3” PART # DESCRIPTION 0603-0467 Short 2” 0603-0468 Medium 3” PART # DESCRIPTION 0603-0469 Long 5.2” RAM DOUBLE-SOCKET ARMS • Marine-grade aluminum with a black powdercoated finish • Fits 1” rubber ball, bases and adapters PART # DESCRIPTION 0603-0470 Double-socket arm w/ swivel DOUBLE-SOCKET ARM WITH SWIVEL • High-strength composite • Consists of double 1” diameter open-ball sockets with a 360° rotation point at the center and a connecting swivel joint that rotates forward and back 180° • The rubber ball and socket at either end and a central pivot point provide unsurpassed adjustability • The RAM ball sockets maximize ball coverage for optimal fit • 5” overall length 0603-0468 0636-0061
RkJQdWJsaXNoZXIy NDI5NTY=