WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2025. SECTION 11 864 See OLDBOOK For Early Model Applications FLUSH-MOUNT MIRROR MOUNT TURN SIGNALS •Low-profile turn signals mount flush to the OEM mirror stems to sit flush with the OEM controls •Die-cast aluminum housings; measure 13/8” L x 9/16” W x 9/16” D •Features five dual-color LEDs with white running light and full-contrast amber turn signal light •Textured satin black finish with smoke lenses PART # DESCRIPTION 2040-3063 For 15-23 FLSTF/FLSTFB/FLSTFBS/FLFB/FLFBS/FLSTC/FLHC/FLHCS/FXSB/FXBR, 18-23 FXBB/FXBBS/FXFB/FXFBS, 18-20 FXLR, 20-23 FXLRS, 22-23 FXLRST, 22 FXRST, 20-23 FXST, 18-21 FLSB, 15-20 FLSTN/FLDE, 15-21 FLSL, 16-17 FXSE, 15 FLSTNSE, 08-13 FLHR/FLHRC/FLHRSE DUAL RAT EYE LED TURN SIGNALS •CNC machined from billet aluminum •Available in gloss black hard anodized finish •Feature two DOT-compliant 18 mm amber or red LED lights per side •Exceptional beam angle •Small compact design •Available in a side-mounted design with wires that exit from the back of the light; lights measure 1.625” L, 0.875” W x 1.6875” T, stand off the bike 1.20” •Single-function design •2010 and earlier models require LED turn signal flasher for use as turn signals, LED turn signal intensifier and load equalizer for the front and rear lights or a control module for use as turn signal/marker lights or LED turn signal intensifier and load equalizer for use as run/b rake/turn signals ASTRO LED TURN SIGNAL/MARKER LIGHTS •Bullet-style super-bright LED turn signal/marker lights really clean up the look of your bike •Each features nine intensely bright LEDs in a cluster module for light output, amazing for its size (roughly 3/4” diameter at the light source) •Available in your choice of amber or red LED light color output •All parts are fully CNC machined from 6061-T6 billet aluminum •Available in your choice of chrome or hard black anodized finishes •May be rotated into virtually any upward-and-downward setting •Dimensions: a little over 1” diameter, 23/8” long, and stand off the bike 11/2” •Sold in pairs LED MINI BULLET LIGHTS •Use as marker lights or auxiliary turn signals •Power leads exit the hollow 3/8”-16 x 5/8” mounting bolt for a clean look •Measure 1” D x 23/4” L •Sold in pairs NOTE: Not DOT compliant. PART # DESCRIPTION 2020-1295 Black/amber PART # DESCRIPTION 2020-1297 Black/red PART # DESCRIPTION CENTER MOUNT MARKER LIGHTS 2020-0442 Chrome finish, amber LED 2020-0441 Black anodized finish, amber LED 2020-0445 Chrome finish, red LED 2020-0444 Black anodized finish, red LED PART # DESCRIPTION ADAPTER PLATES FOR SIDE RAIL-MOUNT MARKER LIGHTS PART #S 2020-0447/2020-0448/2020-0450/2020-0451 2040-0637 For 02-10 Softail, black anodized 2040-1274 For 99-17 Dyna (except FLD), black (requires center mount light) 2040-0640 For 02-10 XL, black anodized PART # DESCRIPTION 2040-0859 Chrome w/ amber LED, smoke lens PART # DESCRIPTION 273515 Gloss black w/ amber LED, smoke lens •Center-Mount Turn Signal Marker Lights can be mounted in almost any 5/16” or 8 mm hole; wires feed through a pre-drilled hole in the mounting bolt •Adapter plates available for your Side Rail Turn Signal Marker Lights, allowing you to remove your stock rear turn signals and replace them with Astros for a narrow look •Made in the U.S.A. NOTE: If being used as turn signals, a load equalizer may be required. NOTE: Not DOT compliant. •26 AWG wire leads measure 48” L •Equipped with IP68 rated JAE connectors for plug-in installation when used with wire adapters PART #s 2050-0492, 2050-0593 and 2050-0494, (sold separately) •Sold in pairs •2011 to pre-CANbus require nothing extra for use as rear turn signals, front lights require a load equalizer; LED turn signal intensifier and load equalizer required for use as front turn signals; LED turn signal intensifier required for use as rear turn signals and run/brake/turn •CANbus front or rear lights require an LED turn signal intensifier •Sold in pairs •Made in the U.S.A. 2040-0859 273515 2020-0442 2040-0640 Shown mounted to marker lights 2020-0441 2020-1295
RkJQdWJsaXNoZXIy NDI5NTY=