WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for the OldBook. SECTION 7 292 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION FOR 84-99 EVOLUTION BIG TWIN 0929-0061 W/ HL2T kit 0929-0004 W/o HL2T kit HYDRAULIC TAPPETS •Rollers have a larger-than-stock inner bearing race that reduces stress and increases axle life •Each lifter body and plunger assembly is hand-fit and pressure-tested to ensure correct operation •Redesigned plunger assembly withstands forces associated with heavy-duty valve springs and pushrods typically used in high-performance applications •Revised metering device precisely controls oil delivery to top end, ensuring rapid lifter pump-up and reducing possibility of oil starvation to bottom end •Tappets that include the HL2T Limited Travel Kit improve cold starts and high rpm valve timing accuracy •Sold in sets of four 0929-0004 PART # DESCRIPTION 213960 For 53-84 Big Twin HYDRAULIC LIFTER CONVERSION KIT •Converts hydraulic lifters to solids while still utilizing the stock pushrods •Sold in set of 4 •Made in the U.S.A. PART # DESCRIPTION 0929-0002 For 66-84 Shovelhead HYDRAULIC LIFTER/TAPPET BLOCK KIT •Fully engineered to utilize Evolution lifters and cams in Shovelhead engines •Includes polished billet lifter blocks, 84-99 style lifter set, gaskets, pushrod clips, mounting hardware and a set of Quickee pushrods •Evolution cams are sold separately •Allows for top end oiling through the pushrods when used with S&S billet Shovelhead rocker covers (sold separately) •Made in the U.S.A. NOTE: Kit requires the use of S&S roller rocker arms (sold separately). SIZE STANDARD HYDRAULIC STANDARD SOLID FOR 66-84 SHOVELHEAD; REPL. OEM #S 18498-48, 18522-53A Std. (0.731”) DS-1943691 DS-194272 +0.005” DS-1943711 - 1 Hydraulic lifter not included. POWERGLIDE™ TAPPETS •These tappets will run in cast iron or aluminum tappet blocks •Recommend fitting the tappets to the blocks with a clearance of 0.0007” to 0.0012” •Produced from billet bearing steel •A true center-line for roller life and exact cam timing •State-of-the-art pushrod seat, machined with the same segmented parabolic cup as the JIMS roller rockers •Hand fit hydraulic unit to a running fit of 0.0002”, with ultra-precision air-gauging system •Made in the U.S.A. DS-194272 DS-194369 PART # DESCRIPTION DS-194107 For 84-99 80” Evolution Big Twin; repl. OEM #18523-86 BIG AXLE™ POWERGLIDE™ TAPPET •Micro-finish bore allows a running fit of 0.0002” •Big Axle™ rollers are designed around three working parts •The outer wheel/roller has a 27% greater wall size – less harmonic distortion for better tracking of cam lobe •Pin bearings are decreased in size by 12%, which increases rpm for more precise tracking •Axle size is increased 36% and doubles as the inner race, so the pin bearing and complete roller assembly now rotate around the axle instead of an inner race, eliminating all possible movement in and around the axle •Std. (0.8425”) size •Sold each •Made in the U.S.A.
RkJQdWJsaXNoZXIy NDI5NTY=