WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 10 All part numbers in BLUE are new for the OldBook. See FATBOOK For Late Model Applications 403 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 2102-0021 3-ohm single-fire coil w/ electronic ignition 3-OHM HIGH-OUTPUT SINGLE-FIRE IGNITION COIL •This single-fire coil is actually two separate coils in a single package •Works well with any single-fire ignition system •Made in the U.S.A. PART # DESCRIPTION FOR 70-84 SHOVELHEAD, 70-85 XL 2101-0345 HI-4N ignition module only 2101-0346 HI-4N ignition module, ignition coil and plug wires HI-4N IGNITION MODULE KIT •More power than the stock ignition •Single-fire and dual-fire function built into a single module •All-metal housing provides improved heat dissipation •Ignition advance and timing degree markings are on the metal flange •Convenient cable notch in the housing makes installation easier and prevents damage to the cable •Sensor and magnet housings are built into the all-metal back plate to protect the sensors from damage during installation •Sensor housings contain advanced flux concentrators with high-temperature-resistant samarium/cobalt magnets for accurate, reliable ignition triggering •Electronics are fully enclosed to resist vibration, moisture and dirt •All electronics are mounted directly to the metal housing, which acts as a heat sink •Four rotary switches for ignition mode selection, advance rate and rev limit •Switches provide accurate, repeatable settings •PART #2101-0346 includes ignition module, S&S ignition coil and correct-length spark plug wires; PART #2101-0345 includes HI-4N ignition module only •Made in the U.S.A. NOTE: Not for fuel-injected models. PART # DESCRIPTION DC6-5 Twin Fire II Miniature, dual output towers TWIN FIRE II COIL •Single-fire just got easier •High-technology materials now make it possible to put two coils in the same space as the stock coil with greater output •No exposed laminations to rust and degrade performance •High voltage and primary terminals machined from brass •High-impact thermoplastic housing is ultrasonically welded and sealed against moisture •Compact size fits easily under stock covers •Peak gap current in excess of 50mA •Over 40,000V per output •Rated at 3-ohms; accepts 7 mm to 8 mm wires •Made in the U.S.A. NOTE: Not for use with DS6-2 ignition system. PART # DESCRIPTION DC6-4 Twin Fire, four output towers TWIN FIRE COIL •Design incorporates two individual performance ignition coils into a single, easy-to-mount package that is only slightly larger than the stock coil and uses the stock mounting bracket •Delivers spark voltage in excess of 30,000V with fast rise times and high energy •For all single-fire, dual-plug head applications •Can be used with any electronic advance ignition system that incorporates dwell control, but cannot be used with the DS6-2 Dyna S or similar ignitions •All coils are rated at 3-ohms •Made in the U.S.A. NOTE: Not for Twin Cam applications. PART # DESCRIPTION 2102-0001 3-ohm, dual tower coil, single-fire, dual-plug (pr.) MINIATURE SERIES COIL •One of the smallest packages delivers high output with advanced magnetic core technology •Designed for use with Dyna 2000 and 3000 series ignitions, factory-installed electronics, or with aftermarket ignitions that employ dwell control •Secondary resistance is 11.5-ohms •Great for customs where coils need to be hidden NOTE: Not for use with the Dyna “S,” DYNA III or earlier generation ignitions. PART # DESCRIPTION DC2-1 1.5-ohm (brown), angled dual output (pr.) DC3-1 3-ohm (green), angled single output, for use with DS-62 single-fire ignition only race application (pr.) DC1-1 3-ohm (green), angled dual output (pr.) DC6-1 3-ohm (green), straight dual output, Std. H-D style (85-up electronic ignition) (ea.) 12V COILS •The “industry standard” with 35,000V spark energies second to none •Designed to work with any Dyna ignition system •Can be used for single- or dual-plug applications •Made in the U.S.A. 2101-0345 PART # DESCRIPTION DC10-1 5-ohm (black), angled single output street application (pr.) DC8-1 5-ohm (black), angled dual output (points) (pr.) DC7-1 5-ohm (black), straight dual output with single-plug heads DC10-1 DC1-1 DC3-1 DC6-1 DC7-1 DC8-1 DC2-1
RkJQdWJsaXNoZXIy NDI5NTY=