WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for the OldBook. SECTION 10 See FATBOOK For Late Model Applications 450 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 2130-0138 For 94-98 Touring models Y POWER TAP HARNESS •Gives you two available ports to tap for 12V switched power; works great for testing, using the OBDP and keeping your optional accessory plug in at the same time •Made in the U.S.A. PART # DESCRIPTION 2120-0604 Auxiliary lamp wiring harness; repl. OEM #68355-05 AUXILIARY LAMP WIRING HARNESS •Allows mounting of late-style 4 1/2” auxiliary lamps equipped with spade connectors on pre-05 models •Sold each •Requires two harnesses •Made in the U.S.A. PART # DESCRIPTION OEM-TYPE CONNECTORS 2120-0825 For all 95-99 Evolution Big Twin, OEM engine temp Delphi connector w/ terminals; repl. OEM #72273-95 2120-0823 For 95-99 Evolution Big Twin, OEM-type throttle position sensor (TPS) Delphi connector w/ terminals; repl. OEM #72280-95 PART # DESCRIPTION DELPHI CONNECTORS 2120-0822 For 98-99 Evolution Big Twin, connects map sensor; repl. OEM #72230-98 2120-0821 For 95-98 FLHT/FLHR/FLTR, connects front fuel injector and rear fuel injector; repl. OEM #72244-95 CONNECTORS WITH WIRE PIGTAILS •OEM-style and Delphi connectors with 18” wire pigtails •Wiring matches OEM colors for easy installation •Made in the U.S.A. PART # DESCRIPTION 2120-0769 Wiring harness COMPLETE BIKE HARNESS •The perfect start for any project bike or OEM model re-wire •Complete bike harness with starter relay, 3-circuits, self-canceling and run, brake and turn signal module •Works with any stand-alone Evo or Twin Cam ignition system •Designed to operate with a two-position key switch •Key start switches can be used with a simple wiring modification (ignition system and key switch are not included with this harness) •OEM color-matching harness with 11-second self-canceling turn signal module •Fuse block holds a full size, commonly available and replaceable starter relay and three ATO fuses •A 30-Amp circuit breaker is installed and is ready for any regulator/charging system •Harness provides running light and turn signal functions to the front turn signals, run, brake and turn signal functions for the rear turn signals •Oil, neutral, high beam and turn signal indicator wiring •Color-matching handlebar switch wiring, as found on most 96-13 models (except Dresser models) •Headlight wiring with headlight socket and terminals •Front turn signal connectors and terminals •Rear fender harness with connectors and terminals •Key switch wiring with ring terminals •Coil wire with ring terminals, tachometer, horn, oil sending unit, brake switch and neutral switch wiring with terminals •Sections of 3/16”, 1/4”, 3/8” and 1/2” ID heat shrink included •Heavy-gauge, 12 (+) power and (-) ground wires with terminals for battery connection •Made in the U.S.A. 2120-0821 2120-0825
RkJQdWJsaXNoZXIy NDI5NTY=