BOLD MAGENTA part numbers are new for 2025 HANDLEBARS & HAND CONTROLS PARTSCANADA.COM STREET | 2025 HANDLEBARS & HAND CONTROLS 407 DESCRIPTION PART # Push-Pull SE Throttle 0632-0978 PUSH-PULL SE THROTTLE •Updated design of the Motion Pro Push-Pull throttle •Die-cast aluminum housing •Smooth painted black finish •Stainless steel hardware •Fits 7/8” (22 mm) bars •Opens carburetors up to 38 mm •Perfect for smooth-bore conversions on street and race bikes •Special cables available to fit most conversions •Includes nylon throttle tube with grip retaining ring and pop out end cap •Maximum twist 165°/maximum travel 45 mm DESCRIPTION PART # Enhanced handlebar mount switch 0616-0232 ENHANCED RIGHT SIDE HANDLEBAR MOUNT START/STOP SWITCH • Required for installation of Revolver Throttle Kit on bikes with ignition and starter switches in stock throttle assembly •Fits 7/8” bars (22.2 mm) •Extra-narrow design is only 26 mm wide •Push In/Out engine switch •Momentary 2-pole starter switch • Starter switch has two separate circuits, one normally open, one normally closed for street bikes that use a headlight/starter cutoff •550 mm long wiring harness with brake light switch circuit wiring •Brake light circuit wiring pigtail 120 mm long with female spade connectors •Stainless steel screws and internal rubber pad positions switch on handlebar securely without drilling holes • Wiring harness has bare, tinned wires without connector for easy installation of OE connector body •Made in Italy by Domino THROTTLES AND REPLACEMENT PARTS DESCRIPTION PART # Throttle – black BA-01058 Repl. throttle sleeve for PART #s BA-01058 and BA-01059 BA-01052 Dual sport throttle – black 875039 Universal throttle cable – pull K28-9900 THROTTLE KITS FITS MODEL PART # UNIVERSAL Models w/ Mikuni smooth-bore conversion kit (MP throttle 01-0073, cable 01-0402) 875130 Models w/ Mikuni smooth-bore conversion dual throttle only 875039 Models w/ Mikuni smooth-bore conversion throttle only BA-01058 Models w/ Mikuni smooth-bore conversion throttle cable only (01-0233) K28-9900 PUSH/PULL THROTTLES AND KITS •Perfect for smoothbore carburetor conversions on street and race bikes •Designed to open up to 38 mm carburetors •Kits include Motion Pro Push-Pull throttle and throttle cable to work with stock carb (includes carb cap if needed) •Dual-sport throttle fits 7/8” handlebars and includes throttle tube; compatible with Yamaha FZR and XT models •Universal cables fit all bikes with Mikuni Smoothbore carbs (measures 39.5” long) • Die-cast aluminum housing, available with chrome or black epoxy finish BA-01058 FITS MODEL PART # HUSABERG FS 450 Super Moto 04-06, 08 0632-0506 FS 550 Super Moto 07 0632-0506 FS 570S Street Legal FI 11 0632-0506 FE 650 04-09 0632-0506 FS 650 Super Moto 0632-0506 FITS MODEL PART # KTM 350 EXC-F 12-16 0632-0506 450 SMR Super Moto 04-09, 12 0632-0506 500 EXC 12-16 0632-0506 525 SMR Super Moto 04-05 0632-0506 690 Enduro R 08-14 0632-0506 FITS MODEL PART # YAMAHA XT225 01-07, XT250 08-18 0632-0505 WR250R Dual Sport 08-18 0632-0505 WR250X Super Moto 08-11 0632-0505 TITAN THROTTLE SLEEVES •Tougher and more resilient than aluminum tubes •Will not deform and seize upon a hard impact like aluminum tubes can •No more DNFs due to bent or broken throttle tubes •Proprietary low-friction material provides smooth operation and eliminates galling •No irritating and uncomfortable vibration like aluminum tubes •Higher performance than aluminum tubes at a much lower cost •Cannot be used with bar end-mounted hand guards 0632-0506 0632-0505
RkJQdWJsaXNoZXIy NDI5NTY=