BOLD MAGENTA part numbers are new for 2025 SERVICE & MAINTENANCE TOOLS PARTSCANADA.COM TIRE & SERVICE | 2025 SERVICE & MAINTENANCE TOOLS 365 DESCRIPTION PART # BPF Rod Guide Wrench 41/43 mm 3805-0192 BPF ROD GUIDE WRENCH •Used to remove internal rod guide on Showa BPF 41 and 43 mm forks •Black oxide finish •43 mm side replaces Honda OEM tool 070MB-MGPA100, Kawasaki OEM tool 57001-1758 and Suzuki OEM tool 09940-84710 •41 mm side replaces Honda OEM tool 070MB-MCJ0100, Kawasaki OEM tool 57001-1742 and Suzuki OEM tool 09910-84711 DESCRIPTION PART # Fork alignment tool 3801-0115 FORKTRU FORK ALIGNMENT TOOL •Quick and easy-to-use tool for aligning front forks to ensure they are parallel from top to bottom •Knurled adjustment screws for easy setup • Proper alignment reduces stiction, enhancing fork performance •Reduces seal and bushing wear •Fits most MX and off-road motorcycles (does not work on most sport bikes due to large brake rotor diameter and 17” wheel diameter) •Will work on 27 to 62 mm fork legs and tubes • Works on forks that are 140 to 220 mm (5.5” to 8.6”) on center FITS MODEL PART # HONDA CRF250R/X 04-09,12, CRF450R 02-08, CRF450X 05-09,12 (Showa 46 mm and 50 mm Twin-Chamber forks) TFCW4650 KAWASAKI KX250 05-07, KX250F 06-12 (Showa 46 mm and 50 mm Twin-Chamber forks) TFCW4650 FITS MODEL PART # KTM 125/144/150/250/450/505 SX/SX-F 07-10, 150 XC 10, 250/350/ 450 SX-F 11-12, 505 XC-F 08-09 (WP 50 mm dual-chamber forks) 3805-0048 SUZUKI RM125 96-07,RM250 96-08, RM-Z250 07-12, RM-Z450 05-12 (Showa 46 mm and 50 mm Twin-Chamber forks) TFCW4650 FORK CAP WRENCHES •PART #TFCW4650 features 46 mm and 50 mm box ends with the ability to remove compression valving on most models •PART #3805-0048 features a hex on one end and a pin spanner on the other to allow access to the inner chamber • Steel with an embossed Race Tech logo on handle DESCRIPTION PART # 46/50 mm fork cap wrench 3805-0162 46/50 MM FORK CAP WRENCH •For removing the caps on Showa MX forks • One end is 46 mm, the other is 50 mm •Can be used for removal of the compression stack •CNC machined for precise fit and tolerance •6061 aluminum material is non-marring on fork caps DESCRIPTION PART # 49 mm, 8-point box wrench for dual-chamber closed-cartridge forks on late-model Honda and Yamaha 3805-0059 DESCRIPTION PART # 50 mm, 6-point box wrench for WP 4860 MXMA dual-chamber closed-cartridge (WP USD 48 mm) forks on late-model KTM 3805-0060 FORK CAP WRENCHES FOR DUAL-CHAMBER FORKS ON HONDA, KTM AND YAMAHA •For removing the fork cap (cartridge) on dual-chamber closed-cartridge forks •12 mm slot for holding the damper rod when removing the rebound bolt; this allows for the removal of the cartridge from the lower fork leg (Honda CRF250R 10 uses fork cap wrench PART #MP08-0236) •Made of billet 6061-T6 and anodized Motion Pro blue •Laser-engraved markings with Motion Pro logo •Original Motion Pro design 3805-0059 3805-0060 3805-0048 TFCW4650
RkJQdWJsaXNoZXIy NDI5NTY=