WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 5 All part numbers in BLUE are new for 2026. 463 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION BAFFLES ONLY 24” L 1860-0237 1.0” dia. 1860-0611 1.25” dia. 1860-0238 1.5” dia. 1860-0461 1.75” dia. PART # DESCRIPTION BAFFLES ONLY (CONT) 24” L (CONT) 1860-0239 2.0” dia. 1860-0240 2.5” dia. 48” L 1860-0241 1.0” dia. 1860-0243 2.0” dia. PART # DESCRIPTION BAFFLE W/ PACKING 24” L 1860-0466 2.0” dia. MUFFLER PACKING ONLY 1860-0468 10” L x 12” W sheet UNIVERSAL BAFFLES •Ideal for replacing rusted-out exhaust baffles •Work great for custom fabrication as well •1.0”, 1.25”, 1.5”, 1.625”, 1.75” and 2.0” OD tubing is 22-gauge stainless steel •All have 1/8” diameter holes, 3/16” staggered centers, 33 holes per square inch and 40% open area PART # DESCRIPTION EMIS* DRAG PIPE BAFFLES DS-202011 1 3/4” (ea.) N/A DS-202012 1 3/4” (pr.) N/A DS-202032 2” (pr.) N/A PART # DESCRIPTION EMIS* INSERTS 1860-2480 Cone reducer kit 2 1860-18181 Louvered (pr.) N/A 1860-06211 Performance (pr.) N/A 1860-18701 Ripper (pr.) N/A 1 Will not fit 2-into-1. HP PLUS® DRAG PIPE BAFFLES AND INSERTS DRAG PIPE BAFFLES •HP Plus® perforate core baffles dampen sound without impeding flow-through performance •All steel construction •Install easily on 1 3/4” or 2”, 16 or 18-gauge drag pipes •Baffles held by 1/4”-20 screws and locking nuts •Sold in pairs or each as noted INSERTS •Create the proper restriction for big torque numbers low in the rpm range or change the sound to your liking •Cone reducer kit adds torque to bottom end; hits hard at 2K rpm •Louvered inserts are best for balanced builds looking for power delivery across the rpm range •Performance inserts are designed for biq torque numbers; hits hard 2K rpm and up PART # DESCRIPTION DS-202019 Repl. steel baffle for 1 3/4” drag pipes REPLACEMENT BAFFLE FOR DRAG SPECIALTIES EXHAUSTS •Sold each PART # DESCRIPTION 1861-0739 For 1 3/4” OD pipes; 8” L 1861-1190 For 2” OD pipes; 6” L 1861-0913 For 2” OD pipes; 9 3/4” L PART # DESCRIPTION 1861-0914 For 2 1/4” OD pipes; 8 1/4” L 1861-0915 For 2 1/2” OD pipes; 8 1/2” L 1861-0916 For 3” OD pipes; 8” L EXHAUST BAFFLES •Fiberglass-wrapped steel construction •May require drilling a hole in the exhaust pipe •Sold each 1860-0468 24” long baffles 1860-0466 1860-0621 1860-1818 1860-1870 1860-2480 DS-202012 •Plug reduces noise and comply with SAE J2825 sound test with no appreciable loss of performance •Ripper inserts create the noise, allowing your bike to be heard •Sound kit takes off 4 dB at idle and improves low-end torque with minimal loss of top-end horsepower •Easy installation with basic hand tools 1861-0739 •3.0” OD tubing is 16-gauge stainless steel •Perforated sheet and 2.5” OD tubing are 20-gauge stainless steel •Sold each •Made in the U.S.A.
RkJQdWJsaXNoZXIy NDI5NTY=