WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 5 All part numbers in BLUE are new for 2026. 465 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 1861-0153 2” W x 3’ L heat shield strip PART # DESCRIPTION M30051 18” x 18” heat shield sheet HEAT SHIELD •Aluminized heat barrier with adhesive backing •Foil-coated fiberglass cloth adheres to body panels to protect plastic or fiberglass from engine or exhaust heat •One 18” x 18” sheet provides 324 square inches of superior heat protection •Also available in a long narrow strip, sized 2” W x 3’ L •Made in the U.S.A. PART # DESCRIPTION 1860-1383 For 17-24 FLHT/FLHR/FLHX/FLTRX/FLTRU/FLTRK w/ OEM or aftermarket mufflers (set includes 1.75” reaction block stainless steel clamp for left muffler and a 2.5” version for the right) PART # DESCRIPTION 1860-1382 For 99-16 FLHT/FLHR/FLHX/FLTR w/ 2” inlet mufflers (set includes two 2” reaction block stainless steel clamps) 1860-0667 Replace 1” W OEM muffler clamps; fit mufflers with 1.75” ID inlets; repl. OEM #65296-95A STAINLESS STEEL MUFFLER CLAMPS •Feature a 1.25” wide stainless band with an exclusive reaction block for 360° clamping without muffler or header distortion •High-strength fastener hardware with corrosion-resistant coating included PART # DESCRIPTION 0930-0136 Exhaust stud EXHAUST STUD •5/16”-18, 5/16”-24 x 1.910” •Zinc-plated steel PART # DESCRIPTION 1860-2235 Hinged P-clamp kit for crossover exhaust for 99-23 FL Touring HINGED P-CLAMP KIT FOR CROSSOVER EXHAUST •Steel construction •Sold as a kit PART # DESCRIPTION DS-209970 For 99-05 Dyna MIDWAY EXHAUST MOUNTING KIT •Relocates rear midway support clamp off rear pipe bend for improved mounting and appearance •Chrome kit includes two 1 3/4” pipe clamps (one each for the rear and the front) and one mounting hanger bracket •Fits Drag Specialties and other exhaust pipes PART # DESCRIPTION FOR 99-24 FLHT/FLHR/FLHX/FLTRX/FLTRU/FLTRK 1861-1518 Support kit; repl. OEM #s 65723-85, 65724-85 and 3929 1861-1517 Replacement bracket only; repl. OEM #65723-85 EXHAUST SUPPORT KIT •Kit includes bracket, rubber mount and bolts needed to support one side of the exhaust system PART # DESCRIPTION DS-203060 3” L PART # DESCRIPTION DS-203070 4 3/4” L EXHAUST HANGER BRACKETS •Chromed 1/8” thick steel exhaust hangers •Sold each PART # DESCRIPTION FOR 99-06 FLT/FLHT/FLHR/FLHX/FLTR 1861-1109 Silver; repl. OEM #65678-85D REAR EXHAUST PIPE BRACKET • High-quality replacement component •Zinc-plated steel DS-203060 DS-203070 1861-1517 1861-1518 1860-0667 1860-1383 1861-0153 M30051 •Sold each •Made in the U.S.A. •Sold in pairs •Made in the U.S.A.
RkJQdWJsaXNoZXIy NDI5NTY=