WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2026. SECTION 7 564 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* 0920-0239 For 17-23 M-Eight Touring 1 MK SERIES CRANKCASE ASSEMBLY FOR M-EIGHT TOURING •Aluminum construction •Reinforced case prevents cracking in high-stress areas for improve reliability •Machined oil scraper allows better oil scavenging; which results in lower temperatures in the flywheel cavity •Designed to fit into the stock frame •Stock deck height •Large volume sump •Accepts all OEM-style components •Can accept larger bores than stock •Includes crankcase assembly, main bearings (2), balancer shaft bearings (2), inner cam bearing, cylinder studs (8), magnetic drain plug, 1/4” pipe plugs (4), front and rear piston cooling jets and gaskets, and all necessary hardware, O-rings and seals for assembly •Black finish •Includes Manufacturers Statement of Origin (MSO) document •Made in the U.S.A. FOR 99-06 TWIN CAM “A” ENGINES (EXCEPT 06 DYNA) PART # DESCRIPTION EMIS* STOCK BORE 0920-01871 Black powdercoat 1 4.125” BORE WITH STOCK STUD PATTERN ONLY 0920-0052 Silver powdercoat 3 1 Exempt per CARB Executive Order (E.O.) #D-355-10 for 99-06 Twin Cam. FOR 07-16 FLHT/FLHR/FLHX/FLTR MODELS PART # DESCRIPTION EMIS* 4.125” BORE WITH STOCK STUD PATTERN ONLY 0920-0093 Black powdercoat 3 0711-0220 Oil line installation kit N/A TWIN CAM ENGINE CASES •Replacement Twin Cam “A” engine cases for stock H-D chassis only (carb and EFI) •Feature greater overall strength than stock crankcases •Strong, dependable Timken®-style sprocket shaft bearings •Clearanced for strokes up to and including 5” •All passages between the crankcase cam support plate are O-ring sealed •Compatible with most stock components •Cam chest has clearance for up to 0.675” lift cams •Include S&S crankcase breather reed valve designed to eliminate oil carry-over and oil scavenging problems •Rear motor mount bolts directly to the stock transmission; fully compatible with the stock primary, charging system, and other stock components •Available with stock bore (ideal for replacement applications), and 4.125” bore engines with stock stud pattern (ideal for custom applications and for use with the S&S 124” Hot Set Up Kit®) •Made in the U.S.A. NOTE: Installation in 99-06 FLT requires oil line installation kit PART #0950-0145, but the stock transmission cover may be used. NOTE: Installation in 07-16 FLHT/FLHR/FLHX/FLTR require an oil line installation kit PART #0711-0220. NOTE: To ease installation in 07-16 FLHT/FLHR/FLHX/FLTR use PART #3802-0054. NOTE: This project requires a skilled technician. It is the responsibility of the person assembling the parts to check all clearances and assembly specifications. 0920-0187 0920-0052
RkJQdWJsaXNoZXIy NDI5NTY=