WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2026. 595 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION FOR 99-17 TWIN CAM 0928-0009 HP+® 0.120” wall thickness PART # DESCRIPTION FOR 99-17 TWIN CAM (CONT) 0928-0010 Race Series® 0.145” wall thickness HP+® AND RACE SERIES® ADJUSTABLE PUSHRODS •Maintain maximum valve lift •Increased stiffness and column rigidity maximizing valve-train stability, increasing engine rpm horsepower and torque output •Adjustable pushrods are 3/8”, 4130 chrome moly tube and use a minimal adjustment parameter eliminating flex and loss of valve train-stability problems associated with most adjustable pushrods •Individual length intake and exhaust pushrods keep the adjustment extension to a minimum •Designed to exceed the needs of performance engines using larger lift camshafts and high spring pressures, while maintaining proper and critical oil flow to top end valve gear •For use with hydraulic or solid lifters and street or race engines •HP+® and Race Series® pushrods require removal of rocker covers and rocker arm supports, Feuling® Quick install rods (PART #0928-0105) can be installed without removing the rocker covers, arms and supports •Feuling HP+ and Race Series pushrods can be used with the factory pushrod tubes •PART #0928-0009 HP+ pushrods have 24 threads per inch adjustment, super strength single jam nut lock system, wall thickness 0.120” •PART #0928-0010 Race Series pushrods have 24 threads per inch with 0.145” wall thickness (recommended when extreme valve-spring pressures are used) •Made in the U.S.A. NOTE: HP+® and Race Series® adjustable pushrods can be adjusted 0.225” over stock length to accommodate longer cylinders and smaller base circle camshafts. NOTE: To ease installation on Twin Cam applications use Pushrod Tube Kit PART #s 0928-0016 or DS-193758; not required. NOTE: Requires removal of rocker covers and rocker arm supports for installation. PART # DESCRIPTION FOR 99-17 TWIN CAM 0928-0105 Quick-install pushrods PART # DESCRIPTION FOR 99-17 TWIN CAM (CONT) 0928-0120 7/16”-20 repl. nut for PART #0928-0105 (ea.) QUICK-INSTALL PUSHRODS •Strongest Quick-Install pushrod on the market •Strength and rigidity of Quick-Install pushrods are second only to heavy-duty one-piece pushrods •Tube material starts out as 7/16” rod OD, then gets turned down to 3/8” OD leaving heavy duty 7/16”-20 threads for the base and jam nut •Jam nut slides up the pushrod •0.134” wall thickness •Base then loosens up into the pushrod to allow Quick-Install access •Individual length exhaust and intake pushrods •Install without the removal of rocker covers •Sold as a set of four •Made in the U.S.A. NOTE: Correct pushrod/lifter adjustment requires starting with fully pumped up lifters. NOTE: Requires Pushrod Tube kit PART #0928-0104 to install (sold separately). NOTE: Quick-Install pushrods have 7/16”-20 threads per inch. 0.050” adjustment per turn. Two turns = 0.100”. 0928-0009 0928-0105
RkJQdWJsaXNoZXIy NDI5NTY=