WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2026. SECTION 7 614 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* FOR 17-25 M-EIGHT (EXCEPT 121” VVT MOTORS) 0925-1176 465 camshaft kit 1 PART # DESCRIPTION EMIS* FOR 17-25 M-EIGHT (EXCEPT 121” VVT MOTORS) (CONT) 0925-1326 472 camshaft kit 1 HP+® CHAIN DRIVE CAMSHAFT KITS FOR M-EIGHT •Include camshafts, lifters and a cam installation kit that includes the cam bearing, cam/crank hardware •Kit also includes gasket/O-ring kit that allows installation of Feuling® Heavy-Duty HP+® 0.0165” wall one-piece pushrods or factory one-piece pushrods •Include HP+ lifters •Made in the U.S.A. •For M-Eight Reaper® cam description and specs see pages 616-617 NOTE: Due to the unstable nature of this 4-valve engine design with one rocker arm activating two valve springs, Feuling® highly recommends running one-piece pushrods (see PART #0928-0091) over quick-install adjustable pushrods to maintain maximum cam/valve lift and reduce valvetrain harmonics and associated hydraulic lifter issues. PART # DESCRIPTION EMIS* FOR 17-25 M-EIGHT (EXCEPT 121” VVT MOTORS) 0925-11771 465 camshaft kit 1 0925-1327 472 camshaft kit 1 0925-1619 487 camshaft kit 3 PART # DESCRIPTION EMIS* FOR 17-25 M-EIGHT (EXCEPT 121” VVT MOTORS) (CONT) 0925-1374 538 camshaft kit 3 0925-1266 592 camshaft kit 3 1 Exempt per CARB Executive Order (E.O.) #D-881 for 17-23 M-Eight engine models only. RACE SERIES® CHAIN DRIVE CAMSHAFT KITS FOR M-EIGHT •Include camshafts, lifters and a cam installation kit that includes the cam bearing, cam/crank hardware •Kit also includes gasket/O-ring kit that allows installation of Feuling® Heavy-Duty HP+® 0.0165” wall one-piece pushrods or factory one-piece pushrods •Includes Race Series® lifters •Made in the U.S.A. •For M-Eight Reaper® cam description and specs see pages 616-617 NOTE: Due to the unstable nature of this 4-valve engine design with one rocker arm activating two valve springs, Feuling® highly recommends running one-piece pushrods (see PART #0928-0091) over quick-install adjustable pushrods to maintain maximum cam/valve lift and reduce valvetrain harmonics and associated hydraulic lifter issues. PART # DESCRIPTION EMIS* FOR 17-19 M-EIGHT TOURING 0925-1345 Chain drive cam 1 PART # DESCRIPTION EMIS* FOR 17-19 M-EIGHT TOURING (CONT) 0925-1346 Gear drive cam 1 GRIND INTAKE OPEN INTAKE CLOSE INTAKE DURATION @ 0.053” INTAKE VALVE LIFT EXHAUST OPEN EXHAUST CLOSE EXHAUST DURATION EXHAUST VALVE LIFT 475C/G Front 6.2° 27.2° 213.5° 0.475” 55.5° 28.5° 263.9° .475” Rear 2.2° 31.2° 213.5° 0.475” 52.2° 20.2° 252.5° .475” 475 CAMSHAFT AND DYNOJET PV-3 KIT •475 camshaft is a bolt-in performance upgrade •Dynojet PV-3 kit means no need for dyno tuning •Displays vehicle data channels in real time •High-contrast display, viewable in direct sunlight •Weather-resistant case for use in all conditions •Made in the U.S.A. NOTE: Exempt per CARB Executive Order (E.O.) #D-355-32 for 17-19 M-Eight Touring models. NOTE: Feuling fastener kit PART #2401-0994 also highly recommended to help prevent cylinder head cracking; kit replaces the rocker shaft bolts with studs and nuts to help reduce the stress of the rocker shaft standoffs. NOTE: Feuling fastener kit PART #2401-0994 also highly recommended to help prevent cylinder head cracking; kit replaces the rocker shaft bolts with studs and nuts to help reduce the stress of the rocker shaft standoffs. NOTE: Not for 23-25 models with 121” VVT motors. NOTE: Exempt per CARB Executive Order (E.O.) #D-881 for 17-23 M-Eight engine models only. 0925-1326 0925-1266 0925-1345 0925-1346
RkJQdWJsaXNoZXIy NDI5NTY=