WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2026. 629 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION CAM DRIVE SPROCKET DS-199175 For 00-06 Twin Cam motors (except 06 Dyna), splined; repl. OEM #25716-99 PART # DESCRIPTION CRANKSHAFT CAM DRIVE SPROCKETS 110798 For 07-17 Twin Cam and 06 Dyna (+4 degrees advance) DS-199074 For all 99-06 Twin Cam motors (except 06 Dyna); repl. OEM #25609-99 PART # DESCRIPTION FOR 17-25 M-EIGHT 0950-08661 Drive gear kit 0950-0863 Pinion gear, undersized 0950-0864 Pinion gear, standard 1 Drive gear only. TWO-GEAR SET FOR M-EIGHT GEAR-DRIVEN CAMS •A two-gear set is required for gear-driven cams that do not come with secondary cam gears •Due to the inherent characteristics of gear drives, you may experience more valve train noise with gear driven cams; oversized and undersized pinion gears are available to help achieve correct gear lash (sold separately) •Drive gear kit and pinion gears must be purchased separately •Made in the U.S.A. NOTE: It is the installer’s responsibility to check all clearances and follow all procedures in the S&S instructions and factory H-D manual. 0950-0866 0950-0864 PART # DESCRIPTION 4-GEAR CAM GEAR DRIVE KIT 0925-0152 For 06 Dyna and all 07-17 Twin Cam DS199532 For 99-06 Twin Cam (except 06 Dyna) 2-GEAR OVERSIZED AND UNDERSIZED GEARS FOR 06 DYNA AND ALL 07-17 TWIN CAM 0925-0094 Pinion gear, undersized PART # DESCRIPTION 2-GEAR OVERSIZED AND UNDERSIZED GEARS (CONT) FOR 06 DYNA AND ALL 07-17 TWIN CAM (CONT) 0925-0095 Pinion gear, oversized FOR 99-06 TWIN CAM MOTORS (EXCEPT 06 DYNA) 0925-0094 Pinion gear, undersized 0925-0095 Pinion gear, oversized GEAR SETS FOR TWIN CAM GEAR-DRIVEN CAMS •A four-gear set is required for gear-driven cams that do not come with secondary cam gears; includes two secondary cam gears, outer cam drive gear, outer pinion drive gear and mounting hardware •Due to the inherent characteristics of gear drives, you may experience more valve train noise with gear driven cams; oversized and undersized gears are available to help achieve correct gear lash •Made in the U.S.A. NOTE: It is the installer’s responsibility to check all clearances and follow all procedures in the S&S instructions and Harley-Davidson manual. 0925-0152 0925-0095 CAM CHAIN DRIVE SPROCKETS •Manufactured from 4340 steel •Cam drive sprockets replace the stock 34-tooth cam drive sprocket and include shims •Crankshaft cam drive is a 17-tooth sprocket that can be used with OEM cam drive sprocket or PART #DS-199009 •Sold each •Made in the U.S.A. DS-199175 DS-199074 PART # DESCRIPTION 0925-0147 Roller conversion cam sprocket ROLLER CONVERSION CAM SPROCKET •34 teeth with ignition trigger ring •Must use with 99-01 engines with stock ignition and cam position sensor •02-06 engines can use stock rear cam drive sprocket •Trigger ring required for 99-01 engines with rear cam drive sprockets to permit engine control system to function correctly PART # DESCRIPTION FOR 17-25 M-EIGHT, 07-17 TWIN CAM MOTORS 0925-1058 Crankshaft cam drive sprocket, 17-tooth; repl. OEM #25673-06 FOR 07-17 TWIN CAM MOTORS 0925-1059 Cam drive sprocket (Twin Cam only), 34-tooth; repl. OEM #25728-06 PART # DESCRIPTION FOR 99-01 TWIN CAM MOTORS 0925-1371 Rear cam outer chain sprocket for engines w/ Magneti Marelli ignition using updated hydraulic chain drive system w/ 07-17 style outer chain, 34-tooth 0925-1370 Rear cam outer chain sprocket for engines w/ Magneti Marelli ignition using factory 99-06 style outer chain, 34-tooth CAM CHAIN DRIVE SPROCKETS •Machined steel, stock replacement roller chain drive sprockets fit 17-25 M-Eight and 07-17 Twin Cam engines as direct replacements and work on early 99-06 engines when upgrading to the hydraulic cam chain tensioners using the roller chain •Made in the U.S.A. •For use with Andrews Twin Cam Conversion Chain Driven Cams; see page 626 •Made in the U.S.A. 0925-1058 0925-1059 0925-1370 0925-1371
RkJQdWJsaXNoZXIy NDI5NTY=