BOLD MAGENTA part numbers are new for 2026 PARTSCANADA.COM 2026 | STREET FUEL/AIR SYSTEMS FUEL/AIR SYSTEMS 1014 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DESCRIPTION PART # 1/4” ID 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 LP (LOW PERMEATION) PREMIUM FUEL LINE •Certified to meet permeation emission standards of 15g/M2/day • On emission-controlled vehicles, check with local and state agencies to determine suitability •Robust multi-layer design and construction •Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids •Ozone and UV light resistant •Wide temperature range from -28.9 to 73.9 °C (20 to 165 °F) •Yellow color for easy identification •Use Stepless® Clamps WARNING: Not for use with fuel-injected engines. NOTE: #SNG-ENAPNR-OA-03. NOTE: Exempt per EPA CARB E.O. #Q-09-028 for offroad use. DESCRIPTION PART # 1/8” ID 3’ Length 877265 25’ Roll 877207 DESCRIPTION PART # 3/16” ID 3’ Length 877266 25’ Roll 877208 DESCRIPTION PART # 1/4” ID 3’ Length 877267 25’ Roll 877209 DESCRIPTION PART # 5/16” ID 25’ Roll 877210 DESCRIPTION PART # 3/8” ID 3’ Length 877269 25’ Roll 877211 PVC VENT LINES • Constructed of soft, flexible plasticized PVC tubing •Safe to use with any type of gasoline or alcohol-type fuel •Smooth hard bore helps prevent interior buildup •Recommended for venting and overflow lines •Flexible down to -17 °C (0 °F) •Maximum dry heat temp is 104 °C (220 °F) DESCRIPTION PART # 3/16” ID 3’ Length 877261 25’ Roll 877212 DESCRIPTION PART # 1/4” ID 3’ Length 877262 25’ Roll 877213 DESCRIPTION PART # 5/16” ID 3’ Length 877263 DESCRIPTION PART # 3/8” ID 3’ Length 877264 BRAIDED FUEL LINES •Nylon-reinforced vinyl fuel line •Braided nylon within the tubing wall provides added strength •Outstanding appearance for custom fuel lines •Flexible down to -3.8 °C (25 °F) •Maximum operating temp is 65 °C (150 °F) DESCRIPTION PART # FUEL LINE, 3’ 1/4”, black M62191 1/4”, clear M6219 DESCRIPTION PART # FUEL LINE, 3’ (CONT) 3/16”, black M62091 3/16”, clear M6209 DESCRIPTION PART # CARB VENT LINE, 5’ 1/8”, black M61091 1/8”, clear M6109 FUEL AND CARBURETOR VENT LINE •This quality-made fuel line will not harden or crack •Fuel line is made of premium polyurethane •Available in 1/4” and 3/16” ID; carburetor vent line available in 1/8” ID • Fuel line available in 3’ lengths • Carb vent line comes in 5’ lengths DESCRIPTION PART # PLAIN – FUEL 1/4”Wx25’L 0706-0014 3/16”Wx25’L 0706-0013 DESCRIPTION PART # PLAIN – FUEL (CONT) 5/16”Wx25’L 0706-0015 DESCRIPTION PART # REINFORCED – FUEL/OIL 1/4”Wx25’L 0711-0060 3/16”Wx25’L 0706-0227 DESCRIPTION PART # REINFORCED – FUEL/OIL (CONT) 5/16”Wx25’L 0711-0061 3/8”Wx25’L 0711-0062 UNIVERSAL FUEL/OIL LINE •Available in plain fuel line or reinforced fuel/oil line •Reinforced line is fuel- and oil-resistant • Sold in 25’ rolls NOTE: Do not use with fuel containing more than 10% alcohol. • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected engines. • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected engines. •Choice of clear or black •Made in the U.S.A. NOTE: Not to be used with fuel over 10% alcohol. 0706-0013 0711-0060 M62191 M6219
RkJQdWJsaXNoZXIy NDI5NTY=