BOLD MAGENTA part numbers are new for 2026 HANDLEBARS & HAND CONTROLS PARTSCANADA.COM STREET | 2026 HANDLEBARS & HAND CONTROLS 407 DESCRIPTION PART # BLACK 2” rise 0602-0842 3” rise 0602-0845 4” rise 0602-0848 CHROME 2” rise 0602-0843 DESCRIPTION PART # CHROME (CONT) 3” rise 0602-0846 MACHINED ALUMINUM 2” rise 0602-0844 3” rise 0602-0847 4” rise 0602-0850 PATRIOT SERIES PIVOTING RISER KITS • Risers can be positioned forward, backward or anywhere in between to allow the rider to truly customize the feel of their bike • Bottom fits 1” handlebar clamps; 1” bar clamp on the top side •Easy installation: remove the current bar, place the stem of the risers where the bar was located previously, then tighten it down; place the handlebar in the top side of the risers and tighten all bolts down securely •Constructed from aircraft-grade aluminum (6061-T6) DESCRIPTION PART # 1 3/4” pivoting bar risers 0602-1451 1 3/4” PIVOTING BAR RISERS FOR KTM 390 ADVENTURE/ DUKE AND HUSQVARNA SVARTPILEN 401 WITHOUT CLIP-ON BARS •1 3/4” (44 1/2 mm) center-to-center rise •Pivots backward/forward based on rider preference •Accepts 26 mm handlebars •Full range of adjustment allows the rider to find their own individual bar position •Always check and confirm that your machine has adequate cable and brake line length before installing handlebar risers •Clutch cable needs to be rerouted behind triple clamp to give enough slack •Sold in pairs •Made in the U.S.A. DESCRIPTION PART # Anti-vibe handlebar risers 0602-0901 ANTI-VIBE HANDLEBAR RISERS FOR BMW R 1200/1250 GSW/GSW ADVENTURE 13-20 •Great add-on for reducing hand tingling/numbness and for improving control across rugged terrain •Anti-Vibe Risers reduce bar vibration and also pivot forward/backward depending on rider preference •Designed to use the stock BMW caps/bolts on the top of the risers •Risers include replacement caps that will be used to tighten the stem of the riser to the OEM triple clamp •Work with stock cables – cable rerouting instructions included in package • 2” of rise •1 1/4” stem •Accept 1 1/4” handlebar •Made in the U.S.A. U.S. Patent # 6,920,806 NOTE: These risers aren’t designed to be positioned straight up because it can be difficult to access the BMW bolts to tighten the stem of the riser in place. DESCRIPTION PART # 1 1/2” barback risers 0602-0903 1 1/2” BARBACK RISERS FOR BMW R 1200/1250 GSW/GSW ADVENTURE 13-20 •1 1/2” of total pullback (moves the bar approximately 1 1/4” up and 3/4” back from the OEM position) •Clear anodized finish •Include mounting hardware •Work with stock cables – cable rerouting instructions provided •Made in the U.S.A. DESCRIPTION PART # Black anodized 0602-0904 DESCRIPTION PART # Gunmetal gray 0602-0905 DESCRIPTION PART # Machine finish 0602-0906 1 1/2” BARBACK RISERS FOR 1 1/8” HANDLEBARS •Move the handlebars 1 1/2” up and 1” back or forward from the OEM position (can be installed facing either direction) •Designed to work on any bike with a stock 1 1/8” Fatbar, parallel OEM bar clamps and open mounting area •Machined from 6061-T6 aircraft-grade billet aluminum • Engraved Rox logo for a clean and understated “factory” look •Always check and confirm that your machine has adequate cable and brake line length before installing handlebar risers •These risers come with two step shims that allow the risers to mount to an OEM step down triple clamp, similar to the Honda Africa Twin •Include all mounting hardware and instructions •Made in the U.S.A. IMPORTANT: These risers cannot be installed on bikes with angled (e.g.,V-shaped) OEM bar clamps. OEM bar clamps must be parallel and sized for M8 bolts in order for these risers to mount properly.These risers will not work on the Triumph Tiger. •Made in the U.S.A. NOTE: Always check and confirm that your machine has adequate cable and brake line length before installing handlebar risers. 0602-0846 0602-0848 0602-0850 0602-0904 0602-0905 0602-0906
RkJQdWJsaXNoZXIy NDI5NTY=