BOLD MAGENTA part numbers are new for 2026 SERVICE & MAINTENANCE TOOLS PARTSCANADA.COM TIRE & SERVICE | 2026 SERVICE & MAINTENANCE TOOLS 375 PIVOT SUSPENSION VISE •Designed to make suspension service simple and quick •Holds shocks and forks securely while you change oil, re-valve, or change seals •Pivoting head holds parts in any position, with mechanical stops every 45° • Aluminum Soft Jaw Vise holds cylindrically shaped parts utilizing a 4-point grip system •Large side holds 39 to 69 mm diameter parts •Small side holds 14 to 39 mm diameter parts • Steel frame is rigid yet has a small footprint, with four pre-drilled holes in the base for secure mounting to a bench • Movable fluid catch pan with mesh insert, and threaded drain bung •Soft Jaw Fork Peg holds fork slider up for removal of dust seal and seal retaining clip •Repositionable bottom slide bar holds forks compressed while bleeding air (priming cartridge) during reassembly and is an excellent platform for adding, adjusting and taking fork oil level measurements DESCRIPTION PART # Pivot suspension vise 3805-0148 FORK LEG HOLDER TOOL •Holds fork legs and tubes for easy hands-free servicing or rebuilding •Mounts in vise to hold fork firmly during repair without causing damage to fork assembly •Will not scratch finish •Made in the U.S.A. DESCRIPTION PART # Fork leg holder tool 3805-0032 FORK SEAL DRIVERS •Split fork seal drivers save headaches and seals •Fit both inverted and conventional forks SIZE PART # 47 to 48 mm TFSD48 SIZE PART # 49 to 50 mm TFSD50 RINGER FORK SEAL DRIVERS •Innovative design makes tool easier and more secure to use than old-fashioned pin-aligned drivers •Anodized aluminum locking ring features knurled finish for secure no-slip grip and positively locks body halves together during use •No more worrying about part of the tool falling off and damaging the fork leg or hitting your feet •Perfectly weighted to drive seals •Body halves are machined from durable carbon steel and feature high-quality protective black e-coat with laser-engraved markings DESCRIPTION PART # 35 to 36 mm 3805-0086 37 mm 3805-0087 39 mm 3805-0088 DESCRIPTION PART # 41 mm 3805-0089 43 mm 3805-0090 45 mm 3805-0091 DESCRIPTION PART # 46 to 47 mm 3805-0092 48 mm 3805-0093 49 mm 3805-0173 DESCRIPTION PART # 50 mm 3805-0174 FORK OIL LEVEL ADJUSTMENT KIT •A fork oil level measurer and adjuster in one •Simply set stop to recommended height, lower into fork and reverse pump to suck oil out until level is reached DESCRIPTION PART # Fork oil level adjustment kit FOL-2 PRO FORK OIL LEVEL TOOL •Use this tool to check and adjust the oil level on conventional and single chamber cartridge forks •Adjustable ring will measure oil levels from 0 to 300 mm in 5 mm increments •Syringe has a capacity of 60 ml •New plunger head design features two fluorocarbon elastomer X-Ring seals that provide superior sealing and chemical resistance •Billet aluminum plunger knob with durable black anodized finish •Plunger head design allows easy cleaning and replacement of seals •Can be used on bicycles equipped with front suspension DESCRIPTION PART # Pro Fork Oil Level Tool 3805-0221 FORK OIL LEVEL KIT • A rugged, accurate measuring scale to adjust fork oil height •Built-in memory device to eliminate guesswork DESCRIPTION PART # Fork oil level kit FOL-1 •Can be used to assist in removing fork compression valve assembly (use of stock front axle required) •Holds shock firmly around shock body, shaft or shock reservoir •Facilitates removal of piston rod and seal head •Facilitates removal of shock reservoir caps, chamber pistons or bladder •Holds shock to remove spherical bearings or needle bearings •Holds shocks for removal of shock spring 3805-0086
RkJQdWJsaXNoZXIy NDI5NTY=